Do Any Of The Comcast X1 Boxes Have Audio Control

RobotPoweredHome is reader-supported. When you buy through links on my blog, I may earn an affiliate committee. As an Amazon Associate, I earn from qualifying purchases.

Earlier last month, my family purchased the Xfinity fix-tiptop box, and forth with it, the Xfinity remote.

Everything was all hunky-dory until one fine night, we constitute out that the volume button wasn't working for some reason.

We were trying to sentinel Netflix and unwind after a hard day, and so this wouldn't practice.

I tried pressing some other buttons, and they seemed to be working fine. And so the problem was only the book buttons.

As I commonly do when I detect myself in a technological pickle, I hopped online to see what I could find on various tech support blogs.

Finally, subsequently hours of enquiry, I found the solution to my problem and then some.

If your Xfinity remote volume is not working, verify that your batteries work. If they do, try unpairing and repairing your remote or resetting both the remote and tv box.

If yous're certain there aren't any hardware defects on the Xfinity remote, contact Xfinity customer care or supercede your device.

Check Your Batteries

If your batteries aren't fully juiced up, that could lead to some of your remote'due south buttons not working.

Also, since button presses lead to IR blasts, and some IR blasts need more juice than others, your batteries may not have enough power to send those signals.

Bank check the expiry date on your batteries to ensure that you're well within the expiry engagement.

If that is not the issue, your batteries may have run out of juice. Get a pair of new batteries and see if the trouble has been resolved.

If your remote has an LED light, and you observe that it flashes red five times, it is an indicator that your batteries are low, and y'all must replace them.

Confirm that in that location aren't any loose connections betwixt the inserted batteries and the remote.

If your volume push button isn't working fifty-fifty after replacing your batteries, information technology is possible that it may be something else.

Unpair and Pair Your Remote Once more

Unpair your Xfinity remote by post-obit these instructions:

Hold down the Setup push button till the light turns green.
Next, enter 9-8-1 and wait for the light-green light to flicker twice.
One time this happens, you'll know that your remote has been unpaired.

At present, if your remote does not have a setup button, just instead you lot find buttons in the class of shapes – Triangle (A), Foursquare (B), Circumvolve (C) and Diamond (D)

Hold downwardly the A and D buttons till you lot see the light turns green.
Similar to the earlier method, enter the number 9-8-1 in order and wait for the light to blink bluish, and you lot'll know that your remote has been unpaired.

At present, if you possess the XR16 Vox Remote, follow these steps to unpair:

Concord down (i) and Dwelling simultaneously till the LED calorie-free starts flashing. Then, in society, press the Ability button, Last arrow (←), and Volume down button.

To Pair your Xfinity remote once again with the Xfinity box TV:

Concur down 'A' on the remote.
On the screen, choose Remote Setup.
Select Yeah for the relevant questions that follow, and practise as instructed by the on-screen instructions.

Check for Bespeak Obstructions

Your Wi-Fi signal won't office properly if there are objects such every bit walls or any kind of furniture blocking its signal.

Similarly, your Xfinity remote volition besides not work if there are obstructions between the device and the remote.

To preclude such an issue from occurring, make sure the pathway is clear and IR signals can accomplish their destination without being rerouted or facing whatever unnecessary hindrances.

Reset Your Remote and Xfinity Box

Performing a mill reset on electronic devices is normally enough to fix any internal malfunctions that may be at that place otherwise, as this reboots your device and clears whatsoever existing data stored or configured. Resetting your Xfinity Remote normally takes care of such problems.

If your remote is the XR15 model, follow these steps :

Hold downwards the A and D buttons simultaneously for about 5 seconds or till the light turns from red → green.
Enter these numbers in a sequence: 9-8-1
You will know the reset has been completed when the LED light turns blue and flickers thrice.

Else, if your remote is the XR11 model, follow these steps:

Hold down the setup button till the light turns from red → green.
Enter the following numbers in lodge: 9-8-one
Y'all will know that your remote is reset when the light turns dark-green and flickers twice.

To reset your Xfinity box, disconnect the power cord, and wait for virtually a minute or so. Now reconnect your device.

Physical Damage to the Remote

Make sure that physical damage that comes to your remote is rectified immediately or every bit soon as possible.

If yous wait besides long to repair the damage, this may result in other hardware defects that will, in the cease, crave y'all to supplant your remote.

If in that location's harm, such as breakage of the dorsum cover of the battery compartment, you should be able to get a replacement from your nearest Comcast Xfinity shop.

Hardware Defect

You must conduct routine checks from time to time of your Xfinity remote and set-top box for any hardware defect that may require your attention.

Confirm that your Xfinity set up-top box is receiving timely updates from Comcast.

If at whatever bespeak you lot call back that the circuit board might take gotten spoiled due to spillage of h2o or any other liquid over it, or if the remote has been dropped from considerable heights, exist sure to contact customer intendance and become your issue resolved.

Supplant the Remote

Now, if your remote has gotten besides banged upwardly and y'all can't possibly repair information technology, you'll have to get information technology replaced.

You can shop for new Xfinity remotes on the website, or you can get them from your nearest Comcast Xfinity outlet.

Instructions for the configuration of your device depending on the model are on the Xfinity website.

If none of these methods works for you, so yous will probably have to contact customer intendance.

Explicate what happened and that y'all need a technician sent to your dwelling house to resolve the aforementioned.

Check the Xfinity official website for contact details and working hours. They also have an banana that you will be able to chat with them in real-time.

Become your Xfinity Remote Volume Working Again

If you lot have multiple Television set boxes, and the particular remote that you are using will only work if aimed at the device that it is paired with.

Naturally, if you wish to utilise a different Television receiver box, you must unpair your remote from the existing connection and repair it with the TV box of your choice.

An easy way would exist to only concur down the Vocalisation button and say 'Program Remote' and and so follow the displayed instructions.

Later on y'all finish pairing your remote with the set-top box, brand sure that you continue following the steps provided to complete setting upward the power, volume, and input control for your TV and audio devices.

Finally, before you perform a factory reset, keep in mind that all the configurations will get erased, and your remote will exist as good every bit new.

You May As well Savor Reading:

How To Access Idiot box Menu With Xfinity Remote?
Xfinity Remote Not Working: How To Fix in Seconds
Xfinity Remote Won't Change Channels: How To Troubleshoot
How To Change TV Input With Xfinity Remote
Xfinity Remote Flashes Dark-green And then Cerise: How To Troubleshoot

Oftentimes Asked Questions

Can I control my Soundbar with my Xfinity Remote?

Yes, all models of Xfinity remotes can be controlled by your Soundbar.

Where is the Setup button on an Xfinity Remote?

Mostly, the setup button is located in line with '0' and below 'vii' on the remote.

What are the ABCD buttons on my Xfinity Remote?

Default settings for the buttons are as follows: A → Assist, B→ Day-, C→ Day+ and D → Descriptive video service on or off.

How do I pair my Xfinity XR15 remote with my Idiot box?

With your Boob tube switched on, press and concur the Xfinity and mute buttons for around 5 seconds till you notice the light turn from red → green. And then, enter the kickoff five digit code listed for the Tv manufacturer.